Roofing dumpster rental in Smithfield
Need a roll-off dropped fast after your Smithfield roof tear-off? We set the container and haul it away same day—no extra trips or cleanup hassles.
Roofing Tear-off Dumpster Sizing by Squares
How big a roll-off do you actually need for a 25-square tear-off in Smithfield? Most roofers use this conversion rule: one square of asphalt shingles equals two-thirds of a cubic yard. Our low-wall 20-yard container handles the tonnage for that job; the low-side design makes it easy to fill the roll-off safely from the ground.
15-Yard Roofing Dumpster
- Capacity: 15 cubic yards
- Fits: 15–20 squares of asphalt shingle
- Best for: Single-layer ranch and bungalow tear-offs
Our 10-yard can fits in any tight driveway and manages shingle weight within legal tonnage for one haul.
20-Yard Roofing Dumpster
- Capacity: 20 cubic yards
- Fits: 25–30 squares of asphalt shingle
- Best for: Most two-story residential tear-offs
The 20-Yard Container works well for roofing jobs because low side walls let crews ground-throw shingles without extra scaffolding.
30-Yard Roofing Dumpster
- Capacity: 30 cubic yards
- Fits: 35–45 squares of asphalt shingle
- Best for: Multi-layer tear-offs and small commercial roofs
A 30-yard bin keeps larger tear-offs moving so crews aren’t stuck waiting on a second haul-out and delayed demobilization.
Asphalt Shingle Weight and Tonnage Planning
The shingle weight is where a three-tab averages 250 pounds; architectural laminate runs closer to 400. A 25-square tear-off lands three to five tons before underlayment is added, so how does that route to a 10-yard dumpster? A hooklift truck keeps weight inside the haul-out limit on one pickup, which is why roofing dumpsters use lower side walls to cap the weight limit.
When you mix shingle debris with framing or sheathing offcuts, we route the container to a general C&D debris service—this keeps the materials compliant. Pure asphalt tear-offs run on a separate stream, so just let us know the contents.
Driveway Placement for Roofing Crew Workflow
We angle the Roll-Off so the swing-door faces the eave, allowing your crew to ground-throw shingles directly into the bin. We lay Driveway Boards under all rollers before the container touches concrete; this prevents damage across your Smithfield property. By maintaining a six-foot tarp perimeter for the nail sweep, you follow asphalt shingle disposal best practices guide. Review our roof tear-off container sizing to stage the right can for your specific job.
Drop angle
Rear door toward the roof line
Set the swing-door end facing the eave where the crew is working to keep walk-in loading and ground-throw paths aligned.
Surface protection
Wooden planks under every roller
Loaded shingle weight can gouge concrete; driveway boards must stay under the rear rollers for the full rental window.
Sweep zone
Six-foot tarp perimeter
Stage magnetic sweepers on the tarp side so your nail cleanup runs in parallel with the loading process.
Tile, Slate, and Metal Roof Tear-off Containers
Concrete tile, natural slate, and standing-seam metal punish a container that was not built for the load: these materials weigh two to four times what asphalt does per square. For these jobs, we route in a reinforced 30-yard low-wall bin with thicker sides and a heavier floor plate; we cap the fill volume well below the rim to keep axle weight legal. We haul these using a lowboy, or provide our general construction debris service for mixed loads.
Same-day Pickup for Fast Roof Project Turnover
Tear-offs run on tight crews; timing matters more than the roll-off. Dispatch coordinates a same-day haul-out that lines up with demobilization, freeing the driveway for inspection or gutter reinstall before the homeowner walks the site. Smithfield crews route the swap-out fast so nothing holds up the next phase!